-
-
Notifications
You must be signed in to change notification settings - Fork 672
FAQ
- What is Marauder
- Can I buy a Marauder
- Can I build my own Marauder
- I bought a Marauder and the screen is just black when I turn it on
- class TFT_eSPI has no member named setTouch or getTouch
- How do I attach the screen to the ESP32
- How do I attach the SD card reader to the ESP32
- Does the Marauder firmware work on other ESP32 devices
- I updated the Marauder and now the touch screen does not work
- My SD card is not detected by the Marauder
- Multiple Definition of
ieee80211_raw_frame_sanity_check
- I tried to compile the firmware and it complained about LVGL
- I can't connect to MarauderOTA when doing the MarauderOTA installation method
- My Flipper dev board reverts back to MarauderOTA after I disconnect it from power
- How do I use different attacks and scans on commandline
- My PCAPs aren't saving
- Compilation error: 'class LinkedList' has no member named 'size'
The ESP32 Marauder is a WiFi and Bluetooth analysis tool. It hosts a suite of capabilities for frame capture, device enumeration, and frame transmission. It is intended to serve as a portable device to stand in for physically larger traffic capturing tools and to provide captured data for post-op analysis.
Yes. We offer official hardware with the firmware preloaded at our shop
Yes, you can build your own Marauder. All you need is an ESP32 development board and a 2.8" ILI9341 TFT touch screen.
There have been some rare cases where the Marauder firmware was wiped from flash during transit through USPS. I am not sure what is causing this but the solution is to compile the firmware from source and upload using the Arduino IDE. Follow the instructions under Installing Firmware.
If you are building the project from source, ensure you are following the steps properly under Installing Firmware. If you are receiving this error, it is because you have not configured your User_Setup.h
. Make sure you copy my User_Setup.h
file into your TFT_eSPI
library folder in your Arduino libraries.
Refer to the wiring documentation shown in IC Connections
Refer to the wiring documentation shown in IC Connections
It is possible to get the Marauder firmware to work on many other ESP32 development boards some type of display. If you want to know if your display will work, check the original TFT_eSPI library. I will not be making changes to the Marauder source to make it function for any other specific displays. If you would like to create your own functionality, you may create a pull request.
If the screen does not work after updating the firmware, it is possible you used the incorrect firmware update file. If you marauder looks like this, then you must use the old_hardware
update file. If your marauder looks like this, then you must use the new_hardware
update file. You can still update your marauder like normal, but thouch coordinates of your marauder are inverted. Imagine the marauder screen being upside down while your try to navigate it. Once you update with the proper firmware, it will return to normal. Following the instructions for Update Firmware
Ensure the size of the SD card you are using is less than or equal to 32GB. If this is the case, try using an SD card by Sandisk. Some other brands of SD card such as Samsung cause the Marauder not to boot properly or not initialize the SD card. You will also want to make sure the SD card is initialized in Fat32. If you are running any version of Marauder earlier than v0.9.15, update to the latest firmware.
Make sure you followed these steps when setting up your Arduino IDE
Make sure you have installed lv-arduino
and not lvgl
in your Arduino IDE
Before you upload the MarauderOTA firmware to your ESP32, try changing the SSID and Password in the code to something different. Once you change it, upload the code and try the OTA update method again. Also make sure you refresh the page immediately after coming to the MarauderOTA update screen.
Ensure you follow the MarauderOTA instructions exactly as they are written. Take great care to follow steps 5, 13, and 16. If that doesn't work, consider using one of the other firmware install options
Check out some of the workflow examples here
Make sure you have followed these instructions for installing the SD card modification on your flipper zero wifi dev board. PCAPs cannot save to the SD card connected to the actual Flipper Zero unless these three conditions are met:
- You are using the
flipper_sd_serial.bin
- You are using a WiFi Dev Board that has an ESP32-S2 with supported connections
- You have enabled the SD Serial option in the Marauder companion app on your Flipper Zero
If these conditions have not been met, it is assumed you are using an SD card modification on your Dev Board or it came with an SD card slot.
If you have already followed those instructions and you are certain you have followed them correctly, make sure you have the SavePCAP
settings enabled. More information for settings can be found here. If that settings is enabled, try running settings -r
to reset your settings.
Go back and install the correct version of ESPAsyncWebServer I have listed here
- Home
- About
- FAQ
- Marauder Versions
- Troubleshooting
-
Getting Started
- Arduino IDE Setup
- DIY Platforms
- Installing Firmware
- Update Firmware
- Hardware
- Status Bar
- Commandline
- Marauder Settings
- Applications
- Thanks
- Countdown Page
- How to make biscuits and sausage gravy