softdevice_controller: rev 2d79a1c86a40b73cf674f90b22d3c480747282ba

CHANGELOG.rst contains the list of changes.

Signed-off-by: Yuxuan Cai <[email protected]>

softdevice_controller/CHANGELOG.rst

@@ -16,6 +16,18 @@ Added
 =====
 
 * Production support for scanning and initiating at the same time. (DRGN-23824)
+* :ref:`Experimental <nrf:software_maturity>` support for Channel Sounding step mode-3.
+* :ref:`Experimental <nrf:software_maturity>` support for Channel Sounding multiple antenna elements.
+* :ref:`Experimental <nrf:software_maturity>` support for the following Channel Sounding HCI commands:
+
+    * LE CS Write Cached Remote Supported Capabilities
+    * LE CS Write Cached Remote FAE Table
+    * LE CS Remove Config
+
+Changes
+=======
+
+* The vendor-specific Set Connection Event Trigger HCI command has been removed. (DRGN-23981)
 
 Bug fixes
 =========
@@ -25,6 +37,7 @@ Bug fixes
   The issue would only happen when the scanner received a long extended advertising packet that did not fit into a single advertising report and the scanning was stopped explicitly or through a timeout. (DRGN-23966)
 * Fixed an issue where the CIS TX Power was set according to the LE Power Control state of the previous CIS in a CIG. (DRGN-21721)
 * Fixed an issue where the BIS receiver running with FEM could enable the radio at the wrong time, causing the receiver to drop packets and lose sync. (DRGN-23891)
+* Fixed an issue where the controller would raise Number Of Completed Packets events for a disconnected CIS. (DRGN-23869)
 
 nRF Connect SDK v2.8.0
 **********************

softdevice_controller/doc/channel_sounding.rst

@@ -11,37 +11,128 @@ LE Channel Sounding (CS) is a feature defined in the `Bluetooth Core Specificati
 CS allows two devices in a connection to perform measurements of their communication channel, both the round trip time (RTT), and the phase and magnitude (as in-phase and quadrature (IQ) values) can be measured.
 The RTT and IQ values can then be sent to an application to calculate the distance between devices.
 
+Support status
+**************
+
 Channel Sounding currently has :ref:`Experimental <nrf:software_maturity>` support in the |controller| for the nRF54L15 SoC.
 CS can be enabled by building with the :kconfig:option:`CONFIG_BT_CTLR_CHANNEL_SOUNDING` Kconfig option enabled.
 
-Developing with CS
-******************
-
-Currently, the :zephyr:code-sample:`bluetooth_hci_uart` sample is recommended to get started with Channel Sounding.
-Build the sample with the following command to enable the CS feature:
+Command support
+---------------
 
-.. code-block:: console
-
-   west build -b nrf54l15dk/nrf54l15/cpuapp --pristine -- -DCONFIG_BT_CTLR_CHANNEL_SOUNDING=y
-
-You can use the sample to run the following supported HCI commands over UART:
+The following LE CS commands are supported:
 
  * LE CS Read Local Supported Capabilities
  * LE CS Read Remote Supported Capabilities
+ * LE CS Write Cached Remote Supported Capabilities
  * LE CS Security Enable
  * LE CS Set Default Settings
  * LE CS Read Remote FAE Table
+ * LE CS Write Cached Remote FAE Table
  * LE CS Create Config
+ * LE CS Remove Config
  * LE CS Set Channel Classification
  * LE CS Set Procedure Parameters
  * LE CS Procedure Enable
  * LE CS Test
  * LE CS Test End
 
-Experimental Limitations
-************************
+Supported capabilities
+----------------------
+
+The |controller| currently has the following supported capabilities:
+
+ * One CS Configuration per ACL connection.
+ * Indefinite Procedure Repeats.
+ * Four Antennas and Four Antenna Paths.
+ * CS Reflector and CS Initiator Roles.
+ * Step modes 1, 2, and 3.
+ * 150 ns time-of-flight precision
+ * RTT with AA-only and 32, 64, 96, and 128 bits random payloads
+ * 1M and 2M CS Sync Phy
+ * No Transmitter Frequency Actuation Error
+
+The supported timing values for the |controller| are as follows:
+
+ * A T_IP1 of 60 µs or greater.
+ * A T_IP2 of 30 µs or greater.
+ * A T_FCS of 60 µs or greater.
+ * A T_PM of 10 µs or greater.
+ * A T_SW of 10 µs.
+
+Multiple antennas support
+-------------------------
+
+Currently, the |controller| supports multiple antennas with a fixed pinout for the multi-antenna switch.
+In order to use the |controller| with multiple antennas, an external GPIO controlled multi-antenna switch needs to be set up with the following truth table:
+
+.. list-table:: Antenna control for multi-antenna switching.
+   :widths: 30 5 5 5 5
+   :header-rows: 1
+
+   * - Active Antenna:
+     - **P1.11**
+     - **P1.12**
+     - **P1.13**
+     - **P1.14**
+   * - Antenna 1
+     - 1
+     - 0
+     - 0
+     - 0
+   * - Antenna 2
+     - 0
+     - 1
+     - 0
+     - 0
+   * - Antenna 3
+     - 0
+     - 0
+     - 1
+     - 0
+   * - Antenna 4
+     - 0
+     - 0
+     - 0
+     - 1
+
+.. note::
+   Currently, the |controller| needs a maximum of 4 µs to trigger an antenna switch within the T_SW period.
+   This means that any multi-antenna switch with the correct pinout must switch within 6 µs to maintain 10 µs T_SW.
+
+Experimental limitations
+------------------------
 
 Currently, the following limitations apply to the :ref:`Experimental <nrf:software_maturity>` support of Channel Sounding:
 
  * :ref:`radio coexistence <nrf:ug_radio_coex>` and :ref:`front-end modules <mpsl_fem>` are not supported.
  * Only one subevent per event is supported in CS.
+
+Developing with CS
+******************
+
+The following samples are recommended for getting started with Channel Sounding:
+
+1. Using the Ranging Service samples:
+
+   * :ref:`Bluetooth: Channel Sounding Initiator with Ranging Requestor <nrf:channel_sounding_ras_initiator>`.
+   * :ref:`Bluetooth: Channel Sounding Reflector with Ranging Responder <nrf:channel_sounding_ras_reflector>`.
+
+2. Using the :zephyr:code-sample:`bluetooth_hci_uart` sample and running HCI commands over UART.
+
+.. note::
+   To build the :zephyr:code-sample:`bluetooth_hci_uart` sample with Channel Sounding enabled, set :kconfig:option:`CONFIG_BT_CTLR_CHANNEL_SOUNDING` to ``y``.
+
+   .. code-block:: console
+
+      west build -b nrf54l15dk/nrf54l15/cpuapp --pristine -- -DCONFIG_BT_CTLR_CHANNEL_SOUNDING=y
+
+Optional CS Kconfigs
+--------------------
+
+Use the following Kconfig options to enable the desired optional CS features:
+
+ * Set :kconfig:option:`BT_CTLR_SDC_CS_STEP_MODE3` to ``y`` to enable Channel Sounding step mode-3 support.
+
+ * Set :kconfig:option:`BT_CTLR_SDC_CS_MAX_ANTENNA_PATHS` to a value between ``2`` and ``4`` to enable Channel Sounding multiple antenna paths support.
+ * Set :kconfig:option:`BT_CTLR_SDC_CS_NUM_ANTENNAS` to a value between ``2`` and :kconfig:option:`BT_CTLR_SDC_CS_MAX_ANTENNA_PATHS` to enable Channel Sounding multiple antennas support.

softdevice_controller/include/sdc_hci_vs.h

@@ -83,8 +83,6 @@ enum sdc_hci_opcode_vs
     SDC_HCI_OPCODE_CMD_VS_READ_AVERAGE_RSSI = 0xfd11,
     /** @brief See @ref sdc_hci_cmd_vs_central_acl_event_spacing_set(). */
     SDC_HCI_OPCODE_CMD_VS_CENTRAL_ACL_EVENT_SPACING_SET = 0xfd12,
-    /** @brief See @ref sdc_hci_cmd_vs_set_conn_event_trigger(). */
-    SDC_HCI_OPCODE_CMD_VS_SET_CONN_EVENT_TRIGGER = 0xfd13,
     /** @brief See @ref sdc_hci_cmd_vs_get_next_conn_event_counter(). */
     SDC_HCI_OPCODE_CMD_VS_GET_NEXT_CONN_EVENT_COUNTER = 0xfd14,
     /** @brief See @ref sdc_hci_cmd_vs_allow_parallel_connection_establishments(). */
@@ -122,21 +120,6 @@ enum sdc_hci_subevent_vs
     SDC_HCI_SUBEVENT_VS_CONN_ANCHOR_POINT_UPDATE_REPORT = 0x82,
 };
 
-/** @brief Connection Event Trigger Role Selection. */
-enum sdc_hci_vs_conn_event_trigger_role
-{
-    /** @brief Unused. */
-    SDC_HCI_VS_CONN_EVENT_TRIGGER_ROLE_UNUSED = 0x00,
-    /** @brief Connection event trigger for the Scanner. */
-    SDC_HCI_VS_CONN_EVENT_TRIGGER_ROLE_SCAN = 0x01,
-    /** @brief Connection event trigger for the Initiator. */
-    SDC_HCI_VS_CONN_EVENT_TRIGGER_ROLE_INIT = 0x02,
-    /** @brief Connection event trigger for connections (Central or Peripheral). */
-    SDC_HCI_VS_CONN_EVENT_TRIGGER_ROLE_CONN = 0x03,
-    /** @brief Connection event trigger for the Advertiser. */
-    SDC_HCI_VS_CONN_EVENT_TRIGGER_ROLE_ADV = 0x04,
-};
-
 /** @brief Peripheral latency disable/enable modes. */
 enum sdc_hci_vs_peripheral_latency_mode
 {
@@ -628,30 +611,6 @@ typedef struct __PACKED __ALIGN(1)
     uint32_t central_acl_event_spacing_us;
 } sdc_hci_cmd_vs_central_acl_event_spacing_set_t;
 
-/** @brief Set Connection Event Trigger command parameter(s). */
-typedef struct __PACKED __ALIGN(1)
-{
-    /** @brief Connection handle to set up trigger for. In case @ref
-     *         sdc_hci_vs_conn_event_trigger_role specifies the Scanner or Initiator, this parameter
-     *         is ignored.
-     */
-    uint16_t conn_handle;
-    /** @brief Selected role to set triggers for. See @ref sdc_hci_vs_conn_event_trigger_role. */
-    uint8_t role;
-    /** @brief (D)PPI channel to use. This channel should be regarded as reserved until the
-     *         connection event (D)PPI task triggering is stopped.
-     */
-    uint8_t ppi_ch_id;
-    /** @brief Task Endpoint to trigger. If this is 0, then the connection event triggering feature
-     *         is disabled.
-     */
-    uint32_t task_endpoint;
-    /** @brief Connection event counter when the task end point triggering should start. */
-    uint16_t conn_evt_counter_start;
-    /** @brief The period in events between triggering of the task end point. */
-    uint16_t period_in_events;
-} sdc_hci_cmd_vs_set_conn_event_trigger_t;
-
 /** @brief Get Next Connection Event Counter command parameter(s). */
 typedef struct __PACKED __ALIGN(1)
 {
@@ -1374,56 +1333,6 @@ uint8_t sdc_hci_cmd_vs_read_average_rssi(const sdc_hci_cmd_vs_read_average_rssi_
  */
 uint8_t sdc_hci_cmd_vs_central_acl_event_spacing_set(const sdc_hci_cmd_vs_central_acl_event_spacing_set_t * p_params);
 
-/** @brief Set Connection Event Trigger.
- *
- * Start triggering a given task on radio event start.
- *
- * When enabled, this feature will trigger a (D)PPI task at the start of radio events.
- *
- * When used for connections, the connection event trigger can be configured to trigger
- * every N connection events starting from a given connection event counter.
- *
- * Disabling scanning, removing the advertising set, or disconnecting the connection will reset the
- * connection event trigger configuration.
- *
- * If the selected (D)PPI channel is reserved by the controller, the controller will
- * return the error code Invalid HCI Command Parameters (0x12).
- *
- * If enabling/disabling the connection event trigger and the trigger is already
- * enabled/disabled, the controller will return the error code Command Disallowed (0x0C).
- *
- * If the role is 0x1, 0x2, or 0x4, and the role is not currently active,
- * the controller will return the error code Command Disallowed (0x0C).
- *
- * If the role is 0x3 and conn_handle does not refer to an active connection, the controller
- * will return the error code Unknown Connection Identifier (0x02).
- *
- * If the role is 0x4 and legacy advertising is used, conn_handle must be set to 0.
- * If extended advertising is used, conn_handle must refer to an active advertising set.
- * Otherwise, the controller will return the error code Unknown Advertising Identifier (0x42).
- *
- * If the role is 0x3 and conn_evt_counter_start has already passed, the controller will return
- * the error code Command Disallowed (0x0C).
- *
- * If the role is 0x3 and period_in_events is zero, the controller will return the error code
- * Invalid HCI Command Parameters (0x12).
- *
- * If the role is 0x1, 0x2, or 0x4 and conn_evt_counter_start or period_in_events is non-zero,
- * the controller will return the error code Invalid HCI Command Parameters (0x12).
- *
- * After HCI Reset, this feature is disabled.
- *
- * Event(s) generated (unless masked away):
- * When the command has completed, an HCI_Command_Complete event shall be generated.
- *
- * @param[in]  p_params Input parameters.
- *
- * @retval 0 if success.
- * @return Returns value between 0x01-0xFF in case of error.
- *         See Vol 2, Part D, Error for a list of error codes and descriptions.
- */
-uint8_t sdc_hci_cmd_vs_set_conn_event_trigger(const sdc_hci_cmd_vs_set_conn_event_trigger_t * p_params);
-
 /** @brief Get Next Connection Event Counter.
  *
  * This command can be used to fetch the upcoming connection event counter value for Centrals or

softdevice_controller/lib/nrf52/hard-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x1063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x106B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:38:50Z'
+timestamp: '2024-12-12T12:43:01Z'

softdevice_controller/lib/nrf52/soft-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x1063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x106B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:38:50Z'
+timestamp: '2024-12-12T12:43:01Z'

softdevice_controller/lib/nrf52/softfp-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x1063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x106B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:38:50Z'
+timestamp: '2024-12-12T12:43:01Z'

softdevice_controller/lib/nrf53/soft-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x2063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x206B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:40:03Z'
+timestamp: '2024-12-12T12:43:40Z'

softdevice_controller/lib/nrf54h/hard-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x4063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x406B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:41:19Z'
+timestamp: '2024-12-12T12:44:38Z'

softdevice_controller/lib/nrf54h/soft-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x4063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x406B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:41:19Z'
+timestamp: '2024-12-12T12:44:38Z'

softdevice_controller/lib/nrf54h/softfp-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x4063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x406B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:41:19Z'
+timestamp: '2024-12-12T12:44:38Z'

softdevice_controller/lib/nrf54l/hard-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x3063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x306B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:42:39Z'
+timestamp: '2024-12-12T12:45:29Z'

softdevice_controller/lib/nrf54l/soft-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x3063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x306B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:42:39Z'
+timestamp: '2024-12-12T12:45:29Z'

softdevice_controller/lib/nrf54l/softfp-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x3063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x306B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:42:39Z'
+timestamp: '2024-12-12T12:45:29Z'

softdevice_controller/lib/nrf54l_ns/hard-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x3063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x306B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:43:48Z'
+timestamp: '2024-12-12T12:46:18Z'

softdevice_controller/lib/nrf54l_ns/soft-float/manifest.yaml

@@ -1,5 +1,5 @@
 description: SoftDevice Controller
-git_revision: 5e894059db09d7b704e6678dc1e38ccc0ce19cd3
-ll_subversion_number: '0x3063'
+git_revision: 2d79a1c86a40b73cf674f90b22d3c480747282ba
+ll_subversion_number: '0x306B'
 ll_version_number: '0x0E'
-timestamp: '2024-12-04T15:43:48Z'
+timestamp: '2024-12-12T12:46:18Z'