Skip to content

Latest commit

 

History

History
185 lines (130 loc) · 5.87 KB

README.rst

File metadata and controls

185 lines (130 loc) · 5.87 KB
Raw

Golioth LightDB Get Sample

Overview

This sample demonstrates how to connect to Golioth and get values from LightDB.

Requirements

  • Golioth credentials
  • Network connectivity

Building and Running

Configure the following Kconfig options based on your Golioth credentials:

  • GOLIOTH_SYSTEM_CLIENT_PSK_ID - PSK ID of registered device
  • GOLIOTH_SYSTEM_CLIENT_PSK - PSK of registered device

by adding these lines to configuration file (e.g. prj.conf):

CONFIG_GOLIOTH_SYSTEM_CLIENT_PSK_ID="my-psk-id"
CONFIG_GOLIOTH_SYSTEM_CLIENT_PSK="my-psk"

Platform specific configuration

QEMU

This application has been built and tested with QEMU x86 (qemu_x86).

On your Linux host computer, open a terminal window, locate the source code of this sample application (i.e., samples/lightdb/get) and type:

$ west build -b qemu_x86 samples/lightdb/get
$ west build -t run

See Networking with QEMU on how to setup networking on host and configure NAT/masquerading to access Internet.

ESP32

Configure the following Kconfig options based on your WiFi AP credentials:

  • GOLIOTH_SAMPLE_WIFI_SSID - WiFi SSID
  • GOLIOTH_SAMPLE_WIFI_PSK - WiFi PSK

by adding these lines to configuration file (e.g. prj.conf or board/esp32.conf):

CONFIG_GOLIOTH_SAMPLE_WIFI_SSID="my-wifi"
CONFIG_GOLIOTH_SAMPLE_WIFI_PSK="my-psk"

On your host computer open a terminal window, locate the source code of this sample application (i.e., samples/lightdb/get) and type:

$ west build -b esp32 samples/lightdb/get
$ west flash

See ESP32 for details on how to use ESP32 board.

nRF52840 DK + ESP32-WROOM-32

This subsection documents using nRF52840 DK running Zephyr with offloaded ESP-AT WiFi driver and ESP32-WROOM-32 module based board (such as ESP32 DevkitC rev. 4) running WiFi stack. See AT Binary Lists for links to ESP-AT binaries and details on how to flash ESP-AT image on ESP chip. Flash ESP chip with following command:

esptool.py write_flash --verify 0x0 PATH_TO_ESP_AT/factory/factory_WROOM-32.bin

Connect nRF52840 DK and ESP32-DevKitC V4 (or other ESP32-WROOM-32 based board) using wires:

nRF52840 DK ESP32-WROOM-32
P1.01 (RX) IO17 (TX)
P1.02 (TX) IO16 (RX)
P1.03 (CTS) IO14 (RTS)
P1.04 (RTS) IO15 (CTS)
P1.05 EN
GND GND

Configure the following Kconfig options based on your WiFi AP credentials:

  • GOLIOTH_SAMPLE_WIFI_SSID - WiFi SSID
  • GOLIOTH_SAMPLE_WIFI_PSK - WiFi PSK

by adding these lines to configuration file (e.g. prj.conf or board/nrf52840dk_nrf52840.conf):

CONFIG_GOLIOTH_SAMPLE_WIFI_SSID="my-wifi"
CONFIG_GOLIOTH_SAMPLE_WIFI_PSK="my-psk"

On your host computer open a terminal window, locate the source code of this sample application (i.e., samples/lightdb/get) and type:

$ west build -b nrf52840dk_nrf52840 samples/lightdb/get
$ west flash

nRF9160 DK

On your host computer open a terminal window, locate the source code of this sample application (i.e., samples/ligthdb/get) and type:

$ west build -b nrf9160dk_nrf9160_ns samples/lightdb/get
$ west flash

Sample output

This is the output from the serial console:

[00:00:00.000,000] <inf> golioth_system: Initializing
[00:00:00.000,000] <inf> net_config: Initializing network
[00:00:00.000,000] <inf> net_config: IPv4 address: 192.0.2.1
[00:00:00.000,000] <dbg> golioth_lightdb: main: Start LightDB get sample
[00:00:00.000,000] <inf> golioth_system: Starting connect
[00:00:00.030,000] <inf> golioth_lightdb: Before request (async)
[00:00:00.030,000] <inf> golioth_lightdb: After request (async)
[00:00:00.030,000] <inf> golioth_system: Client connected!
[00:00:00.030,000] <inf> golioth_lightdb: Counter (async)
                                          31 30                                            |10
[00:00:05.040,000] <inf> golioth_lightdb: Before request (sync)
[00:00:05.040,000] <inf> golioth_lightdb: Counter (sync)
                                          31 30                                            |10
[00:00:05.040,000] <inf> golioth_lightdb: After request (sync)
[00:00:10.050,000] <inf> golioth_lightdb: Before request (async)
[00:00:10.050,000] <inf> golioth_lightdb: After request (async)
[00:00:10.050,000] <inf> golioth_lightdb: Counter (async)
                                          31 31                                            |11
[00:00:15.060,000] <inf> golioth_lightdb: Before request (sync)
[00:00:15.060,000] <inf> golioth_lightdb: Counter (sync)
                                          31 32                                            |12
[00:00:15.060,000] <inf> golioth_lightdb: After request (sync)

Set counter value

The device retrieves the value stored at /counter in LightDB every 5 seconds. The value can be set with:

goliothctl lightdb set <device-name> /counter -b 10
goliothctl lightdb set <device-name> /counter -b 11
goliothctl lightdb set <device-name> /counter -b 12